Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
Right here in the next paragraph you might get lots of reliable information regarding How to Install a Bathtub.
![How to Install a Bathtub: Install an Acrylic Tub and Tub Surround](https://i0.wp.com/www.projectsmallhouse.com/blog/wp-content/uploads/2020/01/OVE_Decors-980208275-Ruby.jpg?resize=500%2C347&ssl=1)
Mounting a tub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is readily easily accessible, the job can move immediately; if you need to open a wall to remove the old bathtub and position the brand-new tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly need an assistant to leave the old bathtub and embeded in the new one. See to it you have certified on your own for the work and are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration utilizing one prior to you start. Possibilities are you might require a professional plumber to make tube connections.
This article will help you set up a new tub in your washroom if you have actually currently acquired a brand-new tub as well as don't require to alter the plan of your previous water system pipes.
Your devices and product checklist must consist of the following:
Getting ready for the Installment
First of all, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to avoid strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the water system. After doing so, activate the taps to drain any water continuing to be in the system. The process of eliminating the existing taps can be fairly problematic because of the limited gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Making use of both wood boards under its feet, position the bath tub in the required placement. The wood boards are valuable in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four little points.
The following goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bathtub up until the level checks out level.
To install taps, fit all-time low of the outermost adaptable tap adapter to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the water supply and also inspect all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bath tub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it right into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washing machines are in area in between the tap and also the sink. Secure the faucet in position with the producer provided backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The previous kind ought to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, causing the water to pass through the wall surface between the bath and the tiling, causing complications with dampness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of soaked newspaper or soft rope. Remember to always load the bathtub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealer can fracture fairly early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the floor tiles making use of waterproof or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
![How to Install a Bathtub Yourself](https://www.makingmanzanita.com/wp-content/uploads/2022/08/leveling-floor-in-bathroom-with-floor-patch-before-install-bathtub-1024x576.jpg)
We hope you enjoyed reading our article on Installing A Bathtub. Many thanks for taking the time to read through our article post. Do you know anybody else who is fascinated by the topic? Take a moment to share it. Thank you for your time. Please come by our blog back soon.
Detail Report this page